Hi

I noticed that in BOINC's starting up messages, where it says 'Found CUDA device' etc, it also says 'est. 60GFlops'

Now this is an 8800GT, which should have about 500GFlops theoretically (according to Wikipedia), and given my 20% overclock, at most 600GFlops.

Judging by the temps, more than 60GFlops is being used.
Is this a problem at all? I gather this only really affects the number of queued WUs, right?


p.s. temps are higher with F@H, so maybe that uses the GPU better, and then Crysis gets temps even higher (perhaps from the memory / texture units?) I suppose the WUs are optimized for the most common GPUs - from the boards it looks like the GF200 series would be the target.

You mentioned F@H, have you seen the FLOP-FAQ ?

I suppose the WUs are optimized for the most common GPUs - from the boards it looks like the GF200 series would be the target.

Hi,

Hadn't seen that FAQ, thanks.

Ok, I was thinking about optimization more in terms of shader vs. memory bandwidth, which is important when optimizing graphics shaders as the ratio varies card to card - perhaps not so important with CUDA.

However, does BOINC's drastic underestimation of my gfx card FLOPS affect anything?

cheers

Some results from the tool CUDA-Z (0.5.95):
http://cuda-z.sourceforge.net/

9800 GX2 (stock 600/1500/1000) @WinXP/32 - not active
BOINC: CUDA device: GeForce 9800 GX2 (driver version 18565, CUDA version 1.1, 512MB, est. 69GFLOPS)
Multiprocessors: 16
GPU Core Performance

• Single-precision Float: 384907 Mflop/s
  Double-precision Float: Not Supported
  32-bit Integer: 77326.2 Miop/s
  24-bit Integer: 385118 Miop/s

GTX 260 192 SP (OC 666/1512/1150) @Windows7/64 host 29460
BOINC: CUDA device: GeForce GTX 260 (driver version 18122, CUDA version 1.3, 896MB, est. 104GFLOPS)
Multiprocessors: 24
GPU Core Performance

• Single-precision Float: 575468 Mflop/s
  
• Double-precision Float: 71788.9 Mflop/s
  32-bit Integer: 103170 Miop/s
  24-bit Integer: 575465 Miop/s

GTX 260 216 SP (OC 666/1512/1150) @WinXP/32 host 23101
BOINC: CUDA device: GeForce GTX 260 (driver version 18206, CUDA version 1.3, 896MB, est. 117GFLOPS)
Multiprocessors: 27
GPU Core Performance

• Single-precision Float: 649640 Mflop/s
  
• Double-precision Float: 80490.2 Mflop/s
  32-bit Integer: 114848 Miop/s
  24-bit Integer: 649810 Miop/s

But I can´t tax the influence of driver, operating system or other factors to these results, they can be coherent within the measurment and this way usable for comparing.

Thanks for that - I noticed you have CUDA 1.3, so i'll update my drivers to see whether that'll help my 8800GT. CUDA-Z reported that it was going at 377Gflops, (20% overclock) I suspect F@H uses the GPU more efficiently with higher Gflops as it makes more heat, but i'm not going to start a new WU to find out! That's what i use the oc for - to speed along GPUGrid - would be too hot for F@H.

Yes, I should have assigned it better: line with "BOINC: ..." is taken from BOINC Manager, not part of CUDA-Z, when it recognizes the abilities to initiate the card for the projects. Sorry for mixing up two different outputs, I thought it was clear.